907 swingarm on 750

ducapiero · **Posted:** Sat Dec 15, 2007 4:55 pm

I found an axle from a monster 600 the diameter is ok 17mm,but the seller says to me that the lenght is 33 cm....
you wrote that i need 35 cm of total axle lenght :shock:

....my question is:
he takes wrong measurement?cause the stock monster swingarm seems to me identical in the end part to 907 one....
i hope it should be fit

lamps
Piero
P.S.
do you think chain register of monster 600 will fit??? :mrgreen:

Tamburinifan · **Posted:** Sun Dec 16, 2007 5:11 pm

M600 has 4,5" rear wheel & a steel swing, thererfore the difference
in axle length I think. M900 w alu swing axle would fit as they have the same
rear wheel as 907.

ducapiero · **Posted:** Tue Dec 18, 2007 2:11 pm

iìm so confused because i have at home 4.5 wheel and i supposed to mount a 170/60-17 on it....but the internal diameter for axle is 17 mm,now if the axle for monster an supersport 600-750 are too shorter i hav to buy one from an St or a 900 monster with alu swingarm....and if the axle of this bike will be too big for my rim??? :oops:

what do you think??
lamps
Piero

Desmo_Demon · **Posted:** Tue Dec 18, 2007 2:27 pm

nilaus · **Posted:** Tue Dec 18, 2007 10:08 pm

Hey guys
Found this site with a 17" conversion. Looks neat.

http://alltomingenting.no-ip.info/gallery/new_rear_axle

Regards

Desmo_Demon · **Posted:** Wed Dec 19, 2007 1:17 pm

nilaus · **Posted:** Wed Dec 19, 2007 2:19 pm

It is a M8. I have a PDF file of the drawing. I can send it to you. Or you can look at this link http://alltomingenting.no-ip.info/paso/Excenter

Regards Klaus

Finnpaso · **Posted:** Wed Dec 19, 2007 3:16 pm

Seems, that link doesnt function... :oops:

ansim · **Posted:** Wed Dec 19, 2007 3:17 pm

nilaus · **Posted:** Wed Dec 19, 2007 8:09 pm

Hi Anders

Is it you’re PASO on http://alltomingenting.no-ip.info/gallery/new_rear_axle ? It looks great with conversion. Have you had any issues? What about clearance between the wheel and swing arm?

Klaus

ansim · **Posted:** Wed Dec 19, 2007 9:00 pm

Yes,

It's mine.

Clearence are very tight.
Chain alignment was tricky.
The wheel I got was not centered in same way as the Paso.
Needed to make some special spacers.

The excenter is available from a UK manufacturer.
But I had it made localy.

//Anders

nilaus · **Posted:** Wed Dec 19, 2007 9:18 pm

What about the depth clearance. I mean does the diameter of the wheel produce a problem. I noticed that the eccentric is at it outer position?

Do you remember where or who in the UK

Klaus

ansim · **Posted:** Wed Dec 19, 2007 9:39 pm

Yes,
The wheel dia is a matter. The exenter have to be in back position, otherwise the tire will scrubbing against the front of the swingarm.

I have Pirelli Diablo 160/60 tiresback.

The bike runs more smooth with 17" tires.

//Anders

ansim · **Posted:** Thu Dec 20, 2007 4:50 pm

Here is the link to the UK manufacturer,

and a view of the excenter they make,

Their produced swingarm on a Monster in Sweden,

//Anders

907 swingarm on 750

Who is online