pricey!
it happened to my original and I mig welded a replacement tab on. simple work. perhaps a buddy has a buzz box in the garage?
| ducatipaso.org http://www.ducatipaso.org/forum/ |
|
| speedo tab washer http://www.ducatipaso.org/forum/viewtopic.php?f=1&t=6332 |
Page 1 of 1 |
| Author: | paisano [ Sat Aug 10, 2013 11:29 am ] |
| Post subject: | speedo tab washer |
tab on my speedo tab washer busted off. Does anyone happen to know if this washer from bevel heaven: https://store.bevelheaven.com/chassis-s ... ab-washer/ will work as a replacement? thanks - Jimmy |
|
| Author: | ir_joep [ Sat Aug 10, 2013 5:08 pm ] |
| Post subject: | Re: speedo tab washer |
Hi, Did happen to me, but I managed to hard solder a piece of metal to it. May be this works for you? cheers Joep |
|
| Author: | randtcastell [ Sat Aug 10, 2013 6:53 pm ] |
| Post subject: | Re: speedo tab washer |
pricey! it happened to my original and I mig welded a replacement tab on. simple work. perhaps a buddy has a buzz box in the garage? |
|
| Author: | Mc tool [ Sun Aug 11, 2013 5:18 am ] |
| Post subject: | Re: speedo tab washer |
Looks like the right bit to me , mine broke too and I also welded it up , but I also gave the speedo drive and the cable a good clean and lube 
|
|
| Author: | paisano [ Sun Aug 11, 2013 11:45 pm ] |
| Post subject: | Re: speedo tab washer |
yeah, I might have to get it welded, but I'm lazy enough that I'd prefer to spend the $$ and slap it in there and not have to worry about it for another 25 yrs. or so. I'll try to get some info from Bevel Heaven on its fitment - I'll keep you all posted. Thanks - Jimmy |
|
| Author: | paisano [ Mon Sep 02, 2013 5:30 pm ] |
| Post subject: | Re: speedo tab washer |
the bevel heaven part fit. cleaned out the little speedo doo-dad while I was at it. what a pain-in-the-ass. Is it just my bike, or does the front wheel fit much better without the washer that goes between the speedo unit and the fork leg? |
|
| Author: | Mc tool [ Mon Sep 02, 2013 7:51 pm ] |
| Post subject: | Re: speedo tab washer |
I don't recall my Paso having that washer but it is shown on the parts diagram . I guess I would put it all together and see weather the discs are centered in the calipers and then either leave or remove the washer to get best alignment . Make sure the brass cable fitting is tight in the ally housing , mine wasn't and it came out and I lost the driven pinion 
|
|
| Author: | paisano [ Mon Sep 02, 2013 9:06 pm ] |
| Post subject: | Re: speedo tab washer |
that washer was in there(somewhere) on mine when I changed the front tire. When I reinstalled the wheel, the brakepads bound too tight, so I removed it. Course, sometime after that my tab washer broke and the timing seemed a little suspicious so I reinstalled it again this time. Same problem with the brakepads. Eh, I removed it again, lets see what happens... |
|
| Author: | paso750 [ Mon Sep 02, 2013 11:07 pm ] |
| Post subject: | Re: speedo tab washer |
| Author: | paisano [ Tue Sep 03, 2013 9:59 am ] |
| Post subject: | Re: speedo tab washer |
Ahhh! You're probably right - thanks. |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|